Bk-precision 4078 - Manual Manual do Utilizador Página 49
- Página / 103
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
The error message is returned in the form
<error number>,"<error description>"
A table of error numbers and their descriptions is presented here.
No error reported
0 No error
Command Errors
A command error is in the range -199 to -100, and indicates that a syntax error was detected. This includes the case
of an unrecognized header. The occurrence of a command error causes the CME bit (bit 5) of the Standard Event
Status Register to be set.
-100 Command Error
-101 Invalid character
-102 Syntax error
-103 Invalid separator
-104 Data type error
-105 GET not allowed
-108 Parameter not allowed
More parameters than allowed were received
-109 Missing parameter
Fewer parameters than necessary were received
-110 Command header error
-111 Header separator error
-112 Program mnemonic too long
The mnemonic must contain no more than 12 characters.
-113 Undefined header
-120 Numeric data error
-121 Invalid character in number
-123 Exponent too large
IEEE 488.2 specifies maximum of 32000
-124 Too many digits
IEEE 488.2 specifies maximum of 255 digits in mantissa.
-128 Numeric data not allowed
A different data type was expected
-131 Invalid suffix
-134 Suffix too long
A maximum of 12 characters are allowed in a suffix.
-138 Suffix not allowed
-140 Character data error.
-141 Invalid character data.
Incorrect character data were received.
-144 Character data too long
Character data may contain no more than 12 characters.
-148 Character data not allowed
-158 String data not allowed
-161 Invalid block data
An error was found in the block data
-168 Block data not allowed
-170 Expression error
Only 6 error ranges may be specified.
-171 Invalid expression
An error was found in the expression.
- Safety Summary 3
- Table of Contents 5
- Section 1 7
- Specifications 8
- Modulation Combinations 10
- Section 2 11
- 2.6 Power Requirements 12
- 2.7 Grounding Requirements 12
- 2.8 Signal Connections 12
- 2.9 RS-232 Connection 12
- 2.11 GPIB Address 13
- 2.10 RS-232 Configuration 13
- Section 3 15
- 3.2 Display Window 16
- 3.3 Front Panel Controls 17
- 3.4 Back Panel Controls 17
- 3.5 Output connectors 18
- 3.6 MENU Keys 18
- 3.6.1 WAVEFORM Keys 20
- 3.6.2 MODE Key 22
- 3.6.3 ARBITRARY Key 23
- Start Address 25
- Markers 25
- 3.6.4 Arbitrary EDIT Menu 26
- 3.6.5 PULSE Menu 29
- 3.6.6 UTILITY Key 29
- 3.6.8 MODULATION Key 32
- 3.7 ON Key 34
- 3.8 Cursor Movement Keys 34
- 3.9 Rotary Input Knob 34
- 3.10 Power-On Settings 34
- 3.11 Memory 35
- 3.12 Displaying Errors 35
- 3.14 Examples 36
- 3.14.6 Using Voltage Offset 39
- 4.1 Overview 40
- 4.2 Device State 41
- 4.4 Device Address 41
- 4.5.1 The Input Buffer 42
- 4.5.2 The Output Queue 42
- 4.5.3 Response Messages 42
- 4.5.4 Coupled Commands 42
- 4.6 Block Data (GPIB Only) 43
- 4.8 Instrument Reset 43
- 4.9 Self Test 43
- 4.10 Command Syntax 43
- 4.11 Status Reporting 47
- 4.11.4 The Error Queue 48
- 4.11.5 Error Codes 48
- 4.12 Common Commands 51
- 4.13.1 SOURce Subsystem 55
- 4.13.1.2 Amplitude 57
- 4.13.1.3 Offset 57
- 4.13.1.5 Function 58
- 4.13.1.6 Point Rate 59
- 4.13.1.7 AM modulation 59
- 4.13.1.8 FM modulation 61
- 4.13.1.9 FSK modulation 62
- 4.13.1.10 Sweep control 64
- 4.13.1.11 PHASe adjust 66
- 4.13.1.12 PULSe setting 66
- 4.13.1.13 Duty Cycle 67
- 4.13.2 OUTPut Subsystem 68
- 4.13.2.1 Output State 68
- 4.13.3 Trigger Subsystem 68
- 4.13.3.1 Trigger Mode 69
- 4.13.3.2 Trigger Source 69
- 4.13.3.3 Burst Count 69
- 4.13.4 Arbitrary Subsystem 70
- 4.13.4.1 Point Rate 71
- 4.13.4.2 Address 71
- 4.13.4.3 Data 72
- 4.13.4.4 Line Draw 73
- 4.13.4.5 Clear 73
- 4.13.4.6 Copy 74
- 4.13.4.10 Start Address 76
- 4.13.4.11 Wavelength 76
- 4.13.4.12 Marker Address 76
- 4.13.4.13 Marker Length 77
- 4.13.4.14 Marker State 77
- 4.13.4.15 Save 77
- 4.13.5 Status Subsystem 78
- 4.13.5.1 Status Preset 78
- 4.13.5.2 Error Queue Read 78
- 4.13.5.3 Error Queue Enable 78
- 4.13.6 System Subsystem 81
- 4.13.6.3 SCPI Version 82
- 4.13.6.4 Security 82
- 4.13.6.5 Power-on Buffer 82
- 4.14.2 DCL - Device Clear 83
- 4.14.4 LLO - Local Lockout 83
- 4.15 SCPI Command Tree 84
- 4.15.4 :TRIGger Subsystem 85
- 4.15.5 :ARBitrary Subsystem 85
- 4.15.6 :STATus Subsystem 86
- 4.15.7 :SYSTem Subsystem 86
- 4.17.1 General 90
- Section 5 94
- 5.3 Performance Tests 95
- 5.3.3 Offset Accuracy 97
- 5.3.4 Sine Distortion 97
- 5.3.7 Operating Modes 98
- 5.3.10 RS232 Capability 100
- Performance Tests Results 101
Manuais e produtos relacionados com Geradores Bk-precision 4078 - Manual
(110 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais