Bk-precision 4034 - Manual Manual do Utilizador Página 7
- Página / 72
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
7
Specifications
NOTE
Specifications listed in manual are applicable after a powered 30 minute warm-up into a 50 Ω load
All timing characteristics are measured at 50% of amplitude with fastest edge
Specifications are verified according to the performance check procedures.
Specifications not verified in the manual are either explanatory notes or general performance characteristics only.
Specifications and information is subject to change without notice. For the most current and correct data please
visit
www.bkprecision.com
MODELS
4033
4034
CHANNELS
1
2
FREQUENCY
0.1 Hz to 50 MHz
TIMING CHARACTERISTICS
PERIOD
Range (single pulse)
20 ns to 10 s (50 MHz to 0.1 Hz repetition rate)
Range (double
pulse)
40 ns to 10 s (25 MHz to 0.1 Hz repetition rate)
Resolution
Up to 6 digits, limited to 10 ps
Accuracy
±
0.01 %
Jitter
< 0.01 % of setting +20 ps on Period, Width and Delay
WIDTH
Range
10 ns to (Period – 10 ns)
Resolution
Up to 6 digits, limited to 100 ps
Accuracy
±
(0.5% of setting +500 ps)
Double Pulse
±
(0.5% of setting +3 ns) for the second pulse
DELAY
Range
0ns to (Period – Width – 10 ns)
Resolution
Up to 6 digits, limited to 100 ps
Accuracy
±(0.5% of setting +500 ps)
DUTY
CYCLE
Range
1 to 99%
Resolution
3 digits (0.1%)
Accuracy
Limited by width and pulse accuracy
OUTPUT CHARACTERISTICS
AMPLITUDE
High Level
Range
-9.90 V to +10 V into 50 ohms load (-19.80 V to +20 V into open circuit)
Low Level
Range
-10 V to +9.90 V into 50 ohms load (-20 V to +19.80 V into open circuit)
Amplitude Range
0.1V to 10V p-p into 50 ohms load (20 Vp-p max into open circuit)
Resolution
3 digits limited to 10 mV
Accuracy
±
1% of setting
±
10 mV into 50 ohms
Aberrations
<5% + 20 mV into 50 ohms load, for pulse levels between ±5 V
Output
Resistance
50 ohms
Offset Accuracy
±
1%
±
25 mV
OPERATING MODES
Continuous
Output continuous at programmed period rate
Triggered
Output quiescent until triggered by an internal, external, GPIB or manual
trigger, then generates one cycle at programmed period rate
Gated
Same as triggered mode except pulses are output for the duration of the
gated signal. The last cycle started is completed
Burst
Same as triggered mode for programmed number of cycles from 2 to
999,999 as set by the N-BURST function
External Width
Trigger duration and rate sets pulse width and repetition
- 50 MHz Programmable Pulse 1
- Generator 1
- Safety Summary 2
- Compliance Statements 3
- Safety Symbols 3
- Table of Contents 4
- Section 1 6
- Specifications 7
- Section 2 9
- 2.6 Power Requirements 10
- 2.7 Grounding Requirements 10
- 2.8 Signal Connections 10
- R Z Z Z1 2 2 1= −( ) 12
- R1 125 125 50 968= − =( ) 12
- 2.9 RS-232 Connection 13
- 2.11 GPIB Address 14
- 2.12 GPIB Connections 14
- 2.10 RS-232 Configuration 14
- Operating Instructions 15
- 3.2 Display Window 16
- 3.3 Front Panel Controls 17
- 3.4 Back Panel Controls 17
- 18
- Model 4034 18
- Model 4033 18
- 3.5 Output connectors 19
- 3.6 MENU Keys 19
- 3.6.1 PARAMETER Menu 20
- 3.6.2 OUTPUT Menu 22
- 3.6.3 PULSE Menu 23
- 3.6.4 MODE Menu 25
- 3.6.5 SETUPS Menu 27
- 3.6.6 UTILITY Menu 28
- 3.7 ON Key 29
- 3.8 Cursor Movement Keys 29
- 3.9 Rotary Input Knob 29
- 3.10 Power-On Settings 30
- 3.11 Memory 30
- 3.12 Displaying Errors 30
- 3.13 Pulse Definitions 31
- 3.15 Pulse Definitions 33
- 4.1 Overview 35
- 4.2 Device State 36
- 4.4 Device Address 37
- 4.7 Instrument Reset 38
- 4.8 Self Test 39
- 4.9 Command Syntax 39
- 4.10 Status Reporting 41
- 4.10.4 The Error Queue 42
- 4.10.5 Error Codes 42
- 4.10.5.1 Command Errors 43
- 4.10.5.2 Execution Errors 43
- 4.10.5.4 Query Errors 44
- 4.10.5.5 System Events 44
- 4.12.1 SOURce Subsystem 49
- 4.12.1.1 Frequency 49
- 4.12.1.2 High Voltage Level 50
- 4.12.1.3 Low Voltage Level 50
- 4.12.1.7 High Voltage Limit 52
- 4.12.1.8 Low Voltage Limit 52
- 4.12.1.9 Pulse Period 53
- 4.12.1.10 Pulse Width 53
- 4.12.1.11 Pulse Delay 54
- 4.12.1.12 Pulse Duty Cycle 54
- 4.12.1.13 Pulse Hold 55
- 4.12.1.14 External Width 55
- 4.12.1.17 Leading Edge Time 56
- 4.12.1.19 Pulse Polarity 58
- 4.12.2 OUTPut Subsystem 59
- 4.12.3 Trigger Subsystem 59
- 4.12.3.1 Trigger Mode 59
- 4.12.3.2 Trigger Source 60
- 4.12.3.3 Burst Count 60
- 4.12.3.6 Trigger Slope 61
- 4.12.4 Status Subsystem 62
- 4.12.4.1 Status Preset 62
- 4.12.4.2 Error Queue Read 62
- 4.12.5 System Subsystem 62
- 4.14 SCPI Command Tree 65
- 4.16 RS-232 Programming 69
Manuais e produtos relacionados com Geradores Bk-precision 4034 - Manual
(106 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais